Blogs/News/PSAs

Hard Gold PCB, immersion gold pcb, is to immerse the board in the plating tank and apply current to form a nickel-gold coating on the copper foil surface of the board. The electro-nickel gold is characterized by high hardness, wear resistance and oxidation resistance. Widely used in applications.

Introduction to Hard Gold PCB Technology:

1. Purpose and role: gold as a precious metal, has good weldability, oxidation resistance, corrosion resistance, small contact resistance, good wear resistance of the alloy and so on;

2. At present, the electroplating gold of the circuit board is mainly a citrate gold bath, which is widely used for its simple maintenance and simple and convenient operation;

3. Water gold content is controlled at about 1 gram / liter, PH value of about 4.5, temperature of 35 degrees, specific gravity of about 14 waves, current density of about 1ASD;

4. The main added drugs are acid-adjusted salt and basic-adjusted salt for adjusting pH value, conductive salt and gold-plated supplement additive for adjusting specific gravity, and gold salt;

5. In order to protect the gold cylinder, a citric acid dip tank should be added in front of the gold cylinder to effectively reduce the pollution of the gold cylinder and maintain the stability of the gold cylinder;

6. After the gold plate is electroplated, a pure water wash is used as the recovery water wash. At the same time, it can also be used to supplement the liquid level of the gold cylinder evaporation change. After the water is washed, it is connected with the second-stage counter current pure water wash. After the gold plate is washed, the alkali liquid is put into 10 g/shdter. To prevent oxidation of the gold plate;

7. Gold cylinder should use platinized titanium mesh as anode, generally stainless steel 316 is easy to dissolve, resulting in nickel-iron-chromium and other metal pollution gold cylinder, causing plating white, exposed plating, blackening and other defects;
8. Gold cylinder organic pollution application of carbon core continuous filtration, and supplemented with appropriate amount of gold plating additives.

What is Immersion Gold Plating:

Everyone chooses immersion gold plating, then what is immersion PCB gold plating, we say the whole plate gold plating, generally refers to "electroplating gold", "electroplated nickel gold plate", "electrolytic gold", "electric gold", "electric nickel plate", soft gold and the distinction between hard gold (usually hard gold is used for gold fingers), the principle is to dissolve nickel and gold (commonly known as gold salt) in chemical potion, dipping the board in the plating tank and turning on the current on the PCB. A nickel-gold plating layer is formed on the surface of the copper foil, and the nickel-gold alloy is widely used in electronic products because of its high hardness, wear resistance, and oxidation resistance.

Electric gold standard: nickel thickness 3-5um; gold thickness 0.25-1.5um; gold thickness minimum 3U''.

The Application of Hard Gold PCB

Hard Gold PCB is widely used in intelligent AI, entertainment, educational robots or other industrial intelligent equipment to expand and contract, rich in change action, frequent separation and contact of local ports of the device, which requires good wear resistance of the PCB at the contact area of the port. Sexual and not easily oxidized.

Welcome to custom Hard Gold Plating PCB directly from Shenzhen PCB Manufacturer at low cost.

7.5W FAST WIRELESS CHARGING

With wireless charging technology developing quickly, wireless charging is an irreversible trend. Wireless charger supplier Meree always works to produce the best cheap dual iphone wireless charger. Meree 10W & 15W fast wireless charger is compatible with Apple 7.5W fast charging function. A standard Qi charger only has an output of 5W, so Meree 10W & 15W fast wireless charger can make you enjoy the fastest charging speed. Our custom dual wireless charger for iphone and apple watch are designed to work seamlessly for your Apple products, which have built-in wireless charging technology. No more cables and you can enjoy the fast speed of wireless charging.

SPECIAL FOR IPHONE, IWATCH AND AIRPODS

Apple announced recently that its long-awaited AirPower pad was canceled. Then will there be a way to wirelessly charge your iPhone, Apple Watch and AirPods all at the same time? Wireless charger manufacturer Meree can provide the custom wireless charging pad for you. Our Meree 3-in-one wirless charger is a special design for Apple fans. The wireless charging pad not only supports the smart phone, but also fits for AirPods and Apple Watch 1/2/3/4. What's more, the inductive charging pad could charge your iPhone, iWatch and AirPods at the same time. You don’t have to prepare three cables but only to put your devices onto the dual wireless iphone charger, then pick and go!

EFFICIENT CHARGING

Meree 10W & 15W fast iphone dual wireless charger guarantees the charging speed as fast as wired charging; also, the multiple device wireless charging pad greatly saves time to charge your devices simultaneously.

UNIVERSAL COMPATIBILITY

Our wireless charging pad is not only designed for Apple products, but also compatible for other brands’ products with built-in wireless technology.

SAFETY ENOUGH

Built-in foreign object recognition, overheating and overcharging prevention, and short-circuit protection features keep your devices safe.

CASE-FRIENDLY

With a charging distance of 6mm-8mm, you don't have to pull off and on the case every time.

Founded in 2007, Meree is devoted to producing wireless charging accessories. We are always committed to growing bigger and making more possibilities. Additionally, we are always concerned about seeking for long-term cooperation. Welcome to join us and make more progress together!

Mounting magnets are comprised of powerful permanent magnets set inside steel cups or channels with countersunk holes or threaded features for holding applications. The steel structure redirects the magnetic field from the back-side of the magnet, making it much more stronger in terms of pull force, and protects the magnetic material from damage during use. Commonly used mounting magnets include Hook Magnets, Threaded Magnets, Countersunk/Counterbore Pot Magnets, Channel Magnets and Rubber Coated Magnets.

Mounting Magnets can double the strength of which you get with the magnet alone, as the steel cup attracting to it is magnetized by the magnet, giving much more pull force. The pull force numbers we list for each product is the force required to pull the mounting magnet straight away from a steel surface.

In fact, how much force a mounting magnet can hold depends on a few factors. When loading the magnet in a different orientation, for example, vertically stuck onto a wall, the weight it can hold up is usually lower than the listed pull force number. Moreover, the friction between the surfaces, the shape of what is being held up, and other factors also contribute to differences of the results.  

Strong mounting magnets are often used as fishing magnets to retrieve objects that are lost underwater with magnetic parts or steel components. Mounting magnets with different features, such as hook, threaded and countersunk, can be widely used for holding, hanging, and attaching objects in different projects.

KAL018 C94 USB C to Lightning Data Cable PD Fast Charger TPE Molding Bend Test 15000 Times

1. Color: White wire and TPE Molding( Other colors can be customized )
2. Wire Material: High quality TPE material
3. Function: Connect USB 3.1 Type-C interface device for charging or connect Apple lightning interface device for charging and high-speed data transmission.
4. Compatible with: iPhone 8/ 8 plus/ X, iPad Pro.

Brand: K123Keytech            SKU: KAL-018

Overview

Connect USB3.1 Type-C interface device, charger and Apple lightning interface device for charging and high-speed data transmission.

High quality TPE material

1. Imported wire.Flame retardant material jacket; High temperature resistance.
2. Bold tinned pure copper wire core, really fast charging.
3. Flexible and durable.

Durability Description

1. Mobile phone interface plug and unload 10,000 times
2. Bend test 5000 times
3. 3KG tensile test

Charging Speed

1. Upgrade high quality core, support 5V/3A fast charging, protect battery from overheating。
2. Fill 50% battery for 30 minutes.

Data Transfer

1. Containing an aluminum foil layer;Anti- interference,stable data transmission.
2. Super speed increase,data transmission spee

MFi Certified

PD fast charging Compatbility with iPhone Xs Max / Xs / XR / X / 8 / 8 Plus.

Normal Carging Compatbility with iPhone 7 /7plus /6 / 6plus / 6s and more.

Specs

Parameter 3A

Wire material

TPE Molding

Compatibility iPhone/iPad/ipod

Function charging/sync

Support PD Fast Charging iPhone 8/ 8 plus/ X, iPad Pro.

Length 3ft / 4ft / 5ft

Transfer Speed 480Mbps

Cable Core 24AWG+30AWG

FAQ

Can this cable output 18W or more with the proper chargers for PD charging?

Thanks for your question. Please note the PD charger with 18W or more output can work well with this USB-C to Lightning cable.

Does this come in a 6 foot ?

What's the housing made of rubber or plastic? I’m not talking about the cable. Thanks!

I have a samsung tablet that does not take the mini plug in. Is there an adaptor to increase the size of the plug?

concern to enterprises. Once the accounts receivable are formed, the accounts receivable customers default, and the case of no one to follow up, due to the stagnation of the company's information and the change of personnel, eventually, lead to overdue, default, or even bad debts. How to avoid the black hole of the company's debts?

From the following procedures, Redstar develops and implements a complete and systematic account receivable risk management system to ensure that the management work runs on a benign track:

1.Accurate and timely customer background survey.

Generally, it includes the following aspects: whether the customer has a fixed place for production and operation, statutory business registration, good credit reputation; Whether the product has a good market prospect; What is the scale of the customer's production and operation and the expected procurement scale? Whether there is a debt dispute in the customer's history and the reasons for disputes; The basic situation of the person in charge of the customer enterprise, the head of the procurement and finance department; The basic situation of the branch of the customer and the affiliated company.

2. Objective and real customer credit survey.

Through detailed investigation and analysis of the customer's business scale, business cycle, liability structure, and property rights ratio, RedStar evaluates the customer's highest credit limit, the longest credit period, and the default procedures.

3. Improve contracts and other written agreements.

It is necessary to establish relevant written treaties between the credit-selling enterprises and the customers, so as to make specific operational provisions for a series of procedures such as receiving orders, delivery receipts, payment settlement, and financial reconciliation.

4. Daily monitoring and management of accounts receivable risk.

Follow up on the customer's business situation and grasp the dynamics of accounts receivable in a timely manner. Especially for overdue accounts, efforts are made to increase the efficiency of the collection of accounts receivable while increasing dunning. For accounts receivable that have not yet expired, supervision should not be loose in case new defaults occur, by doing so, the security of accounts receivable is on the highest level.

For more solutions to accounts receivable risk assessment, please see the following link:

International Contract Default Risk  

In cross-border commercial trade activities, multinational corporations face a serious increase in international trade labor and economic contract breaches, fraud threats risks, including international labor contracts, international investment contracts, international technology transfer contracts, and international sales contracts.                            

International Trade Fraud Risk   

Due to the different countries and regions where the two parties are involved in international trade, and a number of procedures of the sale, transportation, insurance and payment of goods, the mutual influence and restraint of the two parties are weak, it is not easy to be detected when fraudsters implement frauds.            

International Trade Payment Settlement Risk  

The risk of international trade payment settlement is mainly reflected in the lack of effective understanding of foreign customers before trading transactions, and it is unable to obtain sufficient credit for them.

Legal Industry   

In the legal industry, lawyers are the cornerstone of legal procedures. In general, investigation and evidence collection is a problem that plagues lawyers, and the legal work required far exceeds the responsibility of the law firm's own employees.   

Debtor Tracking  

The debtor is missing, they change their contact number, change their company name, and of course, move the house. You may have exhausted all available methods and may find it difficult to find the debtor, which disappears with the debt. If the debtor is not found in time, the debt cannot be recovered.        

Litigation and Legal Support

We provide litigation and legal support to our clients. Legal disputes are complex, expensive and time-consuming, and nothing is worse than losing lawsuits. Missing key information or unacceptable evidence lead to losing.

China RedStar corporation is a professional investigation agency providing risk investigation and legal evidence service for enterprises. If you want to know more details or want a quotation, just feel free to contact us!

What kind datas Chile we provided

Chile exports 2015 commodities include copper, fruit, fish products, paper and pulp, wine and chemicals.  Chile is the 42nd largest export economy in the world and the 61st most complex economy according to the Economic Complexity Index (ECI).

Chile import export data and Chile export data actually provided by government customs, Filter by products, shipment dates, ports, country of origin and more

1200 Million Buyers List Expand More Potential Customers Quickly

Our database has more than 130 million traceable companies, allows you to quickly find buyers and suppliers who export the exact targets you need, also including key decision makers name, email, phone, social media, etc... At the same time, we also send potential customers in the supply chain, such as factories, distributors, engineering companies and shopping malls.

List of Purchasers

Find qualified detailed importers and exporters in seconds

Advanced search on10 billion shipment records; Confirm whether shipments are going up or down; Use data to determine health of a company

Target Market Analysis

Detailed charts and data views for the Chile

More than 19 professional reports, used to analyze buyers, suppliers, product sales distribution, etc. in the Chile market, ahead of your competitors and know yourself more

Target Market Analysis

We are professional import export data provider,RFQ today!

• Double layer pure copper       
• 12V/24V optional
  ● 3014 SMD LED                         
• 120 degree
  ● 3 years warranty

Features of 3014 LED specs
1. High power and luminous strip
2. Double layer pure copper 2oz PCB 
3. 3M VHB adhesive tape for easy installation (IE3 with 3M 300LSE tape)
4. High brightness 3014 type LED; 120 degree 
5. Standard 5M on the reel for IE and IE2, 3M on the reel for Ie3
6. IE3 series should work with aluminum profile

Signcomplex Ltd., founded in 2006, focus on supermarket led. If you want to know more details or want a quotation, just feel free to contact us!

Shenzhen xinzhibang Inst. & Eqpt. Co., Ltd company is devoted to produce various precision color meter and precision color tester. And we welcome merchants from all over the world to cooperate with our factory for mutual benefit and win-win, and jointly create a better

On the preservation line, sheets and profiles are thoroughly blast cleaned and provided with a temporary corrosion protection coating. Along with the external transportation unit, the preservation line consists of a pass through blasting machine, a painting unit and a drying tunnel with its associated slat conveyor.

Typical plates widths can vary up to 2500mm, height can vary from 5mm to 1000mm, length can vary from 2000mm to 12000mm.

1. Workpiece conveyor system

The whole roller conveyor system adopts frequency control step-less speed regulation, is able to synchronous running, each department is capable of independent action.

Blast cabinet’ rollers are with special wear-resistant sleeves to prevent blasting abrasion.

Plate chain conveyor with "v" shaped structure, painted steel short-term exposure to avoid film damage.

2. Blasting cleaning

Workpiece detection (measure height) adopted world-famous brand photoelectric detection, workpiece width measurement device send a signal to PLC so as to

automatically adjust abrasive feeding valve opening number.

3. Abrasive cleaning up

First level: Brush+abrasive reclamation

Second level: high-pressure blower blow the workpiece twice one after another after blast cleaning

4. Abrasive reclamation system

Each of the abrasive reclamation system drive points equipped failure alarm function.

5. Dust collector system

Using HR4-48 Donaldson filter material cartridge dust collector, the dust removal efficiency ≥ 99.5%, dust emission is less than 30mg/M3.

6. Spray room

Adopting GRACO X45DL4 high-pressure Airless spraying pump, compression ratio 45:1, flow 38L/min,

Using a standard linear guide trolley, frequency conversion buffer on both ends of trolley stroke. Workpiece detection and transmission system separated from the spray gun set, paint mist interference-free, easy to clean paint scale.

7. Drying room

Adopt dielectric Heaters and hot air circulation principle so that the heat can be fully utilized.

Drying room temperature adjustable from 40℃ to 70℃

Plate chain conveyor systems increase the eccentrical wheels, which saved the problems of deviation and high rate failure.

8. Paint mist filtration devices and harmful gas purifier

This system has automatic explosion-proof alarm function for paint mist concentration. Adopt advanced cardboard to filter paint mist, it is maintenance-free within one year, using activated carbon for adsorption of harmful gases. After this system it will be in accordance with the air pollution emission standards. (Paint mist emission standard ≤ 120mg/M3, p-xylene: emissions concentrations ≤ 70mg/M3, the 15 meters height exhaust pipe allows the secondary emission rate is 1.0kg/h. ）

As one of the most professional shot blasting machine suppliers, QINGGONG MACHINERY’s activity is sales of shot blasting machine China and shot blasting supplies. If you want to know more details or want a quotation, just feel free to contact us!

Related Video

ZGYX 452III DTH Drill Rig

Propaganda film_HD

Taper Tap Fishing Tool

Related Products

ZGYX-424 Combined Mining Rig

Eccentric Overburden Drilling Equipment

7° Tapered Drill Bits

Product Description

Product parameters

PZD：Tapered Bit；

Carbide button shape，D：Ballistic button，Z：Ogive Button；

Maximum diameter of bit，Unit：mm, exaple：036；

Type of powder discharging groove，TC：Regular type，XC：Inclined groove type；

Appendix code，default 01，for length and technologies distinction；

Button quantity，example：0502,05：gauge buttons，02：front buttons；

Bit body information，example：0722,07：internal taper degree，22：internal hole diameter.

ZGYX-424 Combined Mining Rig

This series of products is developed and manufactured by our company, which integrates gas, liquid and automatic control for drilling holes of hydraulic rock drill.

Its standard equipped with cab and automatic brazing mechanism, with leveling and special toothed track walking mechanism, makes the drilling rig has excellent cross-country ability. Dust removal function with bipolar can meet the environmental protection requirements of all mines, products are widely used in various engineering construction and mining. With its high efficiency, energy saving, environmental protection and safety characteristics, it is widely chosen by modern green mines.

Eccentric Reamer System Operating Steps

1.At the beginning of drilling, the eccentric reaming sleeve spins out along the eccentric guide bit and begins reaming to ensure that the casing and drilling system advance simultaneously.

2.When drilling into the right position, carefully reverse, eccentric reaming sleeve cycle, and eccentric drilling system from the casing pull out.

3.The casing is pulled upwards and the concrete slurry or other filler is sprinkled at the bottom of the hole.

4.Conventional drilling tools are used in the bedrock to reach the required depth.

Related News

D535T DTH Drill Rig

ZGYX-420E-1Construction Site_SD

ZGYX-420III-1Construction Site（4）_SD

ZGYX 453 DTH Drill Rig

ZGYX-430 using open hole drill at construction_SD

ZGYX-452Construction Site（1）_SD

ABT Drilling Equipment Co., Ltd. mainly provides drilling rig equipment to help you solve the problem of drilling at high efficiency and low cost. Always feel free to inquiry!

Wine cellars are unique areas in a building designed to store wine,and storage of wine is an important consideration for long-term aging. The three factors that have the most pronounced effect on wine in storage are light,humidity and temperature.

Wine cellar cooling units is generally applied to the whole cellar to ensure the constant temperature and humidity of the cellar.Thenow can supply two types of hsn dehumidifier and self contained unit which are widely used in household,hotel,restaurant, wine cabinet,underground wine cellar,commercial winery,winery warehouse and so on.

1. High precision and Intelligent manufacturing

It adopts Germany imported Rietschle vacuum pump, ultimate vacuum to ensure complete defoaming; the inner tank selects 5mm thick stainless steel plate to effectively prevent rust and easy to clean; specially selects the aviation plug connection line and uses imported sealing glue to effectively guarantee Equipment is airtight.

2. Low cost and high efficiency

Using a rapid china prototyping part or a CNCed model as a master mold, a high-strength silicone mold is produced under vacuum, then to clone the same replica as the prototype. A silicone mold can replicate about 20 products. The processing speed is more than ten times that of CNC, the processing cost is as low as ten or even dozens of times compared with CNC, which greatly improves production efficiency and greatly reduces the development cost, cycle and risk of direct tooling.

3. Small batches production for big size parts

The mold size is up to 1500mmX 1200 mm X 1200 mm, which can efficiently realize the copying of large complex workpieces in small batches production, help to examine the appearance and structural performance of the products, and avoid the risk of direct tooling.

4. Excellent mold operation

The soft molds after solidification molding are all transparent or translucent, have good tensile strength, and are easy to cut and shape.

5. Personalized customization

According to the specific application requirements of the customer, it provides multiple configuration customizations such as vacuum pump configuration, liner material, and operation mode (automatic/manual).

Back profile:

With our automated vacuum casting system, you will get free access to equipment usage training, 3D printing prototype production training, post-treatment process solutions, and lifetime technical support to help optimize production and maximize profit.

Jiangsu Gaxiao also delivers Large HVLS Fans For Church. Large HVLS Fans have air volume 15000m³/min which reduces 7-11degree temperature than perceived temperature.

With Gaxiao permanent magnetic church ceiling fans have the following advantages:

1.Totally silent, is only 36dBA

2.Free maintainence.

3.Small installation space, only 90cm.

4.Long life span, could use more than 10 years

5.Large covering area: The max scope of action of one HVLS industrial fan can reach up to 1800 Sqm.

Our Gaxiao permanent magnetic fans have become most popular for the places which need silent but large volume in the whole world. We believe this fan will be your best choice to save cost and high efficiency.

Jiangsu Gaxiao Environmental Technology Co., ltd a professional hvls fan company in China, and we have various hvls fans for sale. We welcome merchants from all over the world to cooperate with our factory for mutual benefit and win-win, and jointly create a better future. 

6 inch water valve is commonly used with flanged gate valves and various upper valves for water, including dirt separator.
Features of ZECO collector:
1. The release rate of primary gas of water through the exhaust valve assembly is 80%;
2. When the system runs for 4-6 hours, the gas content in the system can be reduced to less than half of the original level;
3. After a period of operation, the gas content in the system can be reduced to 0.4%;
4. Can separate the fouling at the same time during the exhaust;
5. After 50 cycles (flow rate of 0.5m/s), the dirt content decreased to less than 4%;
6. Suitable for systems with frozen liquid content up to 50%;
7. The minimum removal of air bubbles is 10 μm, while the minimum removal of impurity particles is 55μm.
8. The product complies with PED/DEP 97/23/EC(CE) standards;
9. The pressure loss is small and does not affect the flow rate.
6 inch Gate and butterfly valves are normally used in this dirt separator installation to ensure that water flow is blocked during maintenance to meet normal maintenance requirements. The dirt separator is applicable to heating, domestic hot water, geothermal utilization, central heating of thermal power plant, regional heating of boiler, ice storage air conditioning system ice storage and refrigeration and heat exchange & applicable to power industry, petrochemical industry, iron and steel metallurgy, paper, textile industry, food production, aerospace industry, shipping industry, automobile industry and civil heating (refrigeration) and other industries;It is used to protect equipment in the system that has low pressure or is sensitive to dirt because the heating device produces gas easily.

ZECO is one of the most professional control valve manufacturers china , and we have been devoted to produce control valve china for many years. If you want to know more details or want a quotation, just feel free to contact us!

Kamcap is one of the earliest ultracapacitor suppliers in China to develop super capacitor 5.5 v  .

SE series Performance characteristics: standard energy series.

SE series Typical applications: RAM, detonator, car recorder, smart meter, vacuum switch, digital camera, motor drive, clock circuit, UPS, toy, program-controlled switch, etc.

SE Series specification sheet

SP Series Performance characteristics：Standard power series

SP Series Typical applications: RAM, detonator, car recorder, smart meter, vacuum switch, digital camera, motor drive, clock circuit, UPS, toy, program-controlled switch, etc.

SP Series specification sheet

SE -5R5(Connection plate) Product performance list

SP -5R5（Connection plate）Product performance list

Typical Application

As one of the most professional supercapacitor suppliers of china super capacitor, we have been devoting ourselves in providing high quality supercapacitors for sale with competitive price. If you want to buy supercapacitor, don’t hesitate to contact.

Description:

UnitekFiber produces Outdoor Armored PDLC Waterproof Assemblies. The cable is used for outdoor RRU transmitting optical signal and remote fiber feeder etc. Single mode and multi mode is available for chosen. Our PDLC fiber optical cables are with standard duplex LC connectors. All our cables meet the standards of IEC61754-20 and RoHS and REACH materials compliant.

Application:

Multi-purpose Outdoor

For connection between distribution box and RRH

Deployment in Remote Radio Head cell tower applications

Used for 3G 4G Base station

Features:

Standard Duplex LC connector, well connected with standard LC adapter

Available Single mode and Multi-mode

IP67 protection, salt-mist proof, humidity proof, dust proof

Low insertion/return loss, steady optical transmitting.

Light weight, waterproof, dust-proof, moisture proof, Metal hard housing.

The material in the jumpel cable are all-weather and UV-resistant.

Mechanical performance: IEC 61754-20 standard.

RoHS and REACH materials compliant.

Specification

Plastic Foam Pump Bottles Description:

The foam pump bottles bulk is made of food-grade Pet highly crystallized polymer.Pump sprayer cap is made of pp material. It is odorless, tasteless, non-toxic, white and translucent plastics. Its chemical properties are also very stable highly crystalline polymer, surface smooth, glossy, has excellent physical and mechanical properties, long-term use of temperature can reach 120 ℃, pump sprayer with human body engineering design, and convenient to take.The company supports OEM customization and has the ability of independent mold opening design.Proud of our ERP management software .All products can be traced back to raw materials, and the production delivery time is also the industry leading level.Customers are free to choose from natural, white, and amber and other colors. What's more, we plastic bottle manufacturers in china also have a variety of closure options to match with your bottle. Contact us right now!

Plastic Foam Pump Bottles Features:

Better Raw Materials

We Provide You With Reliable Products And High Quality Service

high-quality bottle with FDA, airtight and water-proof

Before your order, we can offer sample products.

Your logo can be printed, embossed, debossed.

Bulk per bag, offer customized package.

Offer custom design, shape, logo, package.

Safe, nontoxic, anti-dust, impermeable.

The pressure nozzle can spray the liquid in the bottle evenly

Plastic Foam Pump Bottles Application

Suitable for a variety of applications including detergents and household chemicals, lubricating oil, chemicals, garden products, pet care, DIY, toiletries, personal health care.

A transmission line in Guangdong, China, and a power supply bureau maintenance engineer come to our factory, said they encountered a headache problem. Transmission lines get through farmland, the line is installed glass insulators. Since Flashover led insulator rupture, fragmentation of insulators scattered into the fields, local farmers stepped on broken glass, complaints Power Supply Bureau, not only caused discontent among the masses, but still give cause transmission security risks. For this special case, power supply bureau engineers hope to find a way to wrap the broken glass insulators, and then be replaced by a professional maintenance engineers.

Fujian Ruisen chemical Co.,Ltd. specially developed;anti-blast splashing RTV coating, added a special aramid fiber pulp (body armor components), not only has the performance of the original RTV silicone rubber coating, but also increase the concentration, effectively enhance the mechanical properties, anti-blasting. This splash-proof coating by the military tests.

We are professional 20M Articulated boom lift manufacturer and factory in China. We can produce Articulating Boom Lifts according to your requirements.

20M Articulated Work Platform Boom Lift Measurements Specifications

20M Articulated Work Platform Boom LiftStandard configuration

Cottonseed oil expeller machine is mainly composed of electrical control, automatic heating, adjustment, transmission, and vacuum oil filter. The screw is carburized by alloy steel to enhance surface hardness and wear resistance. The platter is ground by the surface grinding machine to ensure the finishing coat and increase the oil output. The surface of the machine is treated with stainless steel and chromium plating, meeting food hygiene standards. The commercial importance of the seed of cotton lies in its oil and other products. Cottonseed oil can be used as salad oil and cooking oil. After oil extraction, the residue or seed kernel can be used as livestock feed. Use a cotton gin to remove short lint from seeds. It can then be used to make roving and various fiber products. Seed hulls can be used as coarse feed for animals. Although the ancient Chinese and Indians used crude methods to extract cottonseed oil for medicine and lighting, large-scale industrial use is a new development. Cottonseed is the seed of a cotton crop. The exterior of cottonseed is a hard brown seed shell, and its shape and size vary with the variety. The seed shell contains the embryo, which is the main part of cottonseed, also known as the seed kernel. The oil content of seed kernels can be up to 35-45%, containing about 39% protein and 0.2% gossypol. The cottonseed oil machine can press all oil crops continuously: soybean, peanut, rapeseed, sesame, palm seed, sunflower, cottonseed, tung seed, coconut, olive, rice bran, palm tree, corn husk, etc.

1. Advanced technology and long life

A steel casing is added at the main shaft of the speed reducer of cotton oil mill machinery. Press cage to change single bar to double bar. Adopting high-quality steel, through carburizing quenching or high-frequency quenching, it has the advantages of high hardness, good wear resistance, high precision, running balance and no noise. It satisfies the long-term continuous automatic production and can be used for more than 30 years.

2. High oil yield and large output of cotton oil mill machinery:

The cottonseed oil expeller uses the world's advanced enhanced pressure structure cutters circular row. The pressure of barrel is high. The newly developed four-stage and five-stage compression, the pressure is higher. Their oil yield of soybean is up to 18%, second to none in China.

3. Low energy consumption, labor-saving:

Cotton oil mill machinery adopts infrared heating. It automatically controls temperature, reduces heat loss and shortens heating time. The transmission adopts planetary gear, the first in China. It greatly reduces energy consumption by more than 30 percent. Cottonseed oil machine can achieve automatic control of electrical production and reduce operating personnel.