In the realm of abrasive product, resin fiber discs stand as stalwart companions, serving a myriad of applications, from metalworking to woodworking. These discs, with their reinforced fiber backing and resin-bonded abrasive grains, are designed for precision, efficiency, and durability. However, to unlock their full potential and ensure a prolonged operational life, meticulous attention must be given to their storage and handling. In this comprehensive guide, we will delve into the intricacies of resin fiber discs, exploring the best practices for their storage and handling to optimize performance and longevity.

What Are Resin Fiber Discs?

Resin fiber discs are indispensable tools in various industries, renowned for their versatility in material removal, blending, and finishing applications. The composition of these discs, featuring a robust fiber backing and abrasive grains bonded with resin, enables them to withstand high-speed operations and deliver consistent results. Available in a range of grit sizes and materials, resin fiber discs cater to diverse tasks in metal fabrication, woodworking, and other precision industries.

The Importance of Proper Storage:

1. Climate Control:

Resin fiber discs are sensitive to environmental conditions, and their performance can be significantly affected by temperature and humidity fluctuations. Storing these discs in a climate-controlled environment within the recommended temperature range is crucial. Extreme temperatures can compromise the resin bonding and backing material, leading to diminished performance.

2. Dry Storage:

Moisture, a common adversary for all types of grinding discs, poses a particular threat to resin-bonded discs. Exposure to humidity can degrade the adhesive properties of the resin, resulting in premature failure during use. Therefore, it is imperative to store resin fiber discs in dry conditions, preferably in well-ventilated areas. In instances where discs come into contact with water, thorough drying before use is essential.

3. Avoiding Contamination:

Resin fiber discs should be stored away from chemicals, solvents, and any substances that might compromise their structural integrity. Contaminants can adversely affect the bonding agent, leading to reduced performance and potential safety hazards. A designated storage area free from such contaminants is ideal.

4. Proper Labeling:

Organizing and clearly labeling storage areas for resin fiber discs facilitate easy identification of grit sizes, materials, and intended applications. This organizational strategy streamlines the selection process, preventing errors and optimizing operational efficiency. Well-labeled storage ensures that users can quickly access the right discs for specific tasks.

Best Practices for Handling Resin Fiber Discs:

1. Inspecting for Damage:

Before use, a thorough inspection of each resin fiber disc is paramount. Look for visible signs of damage, including cracks, chips, or irregularities. Discard any discs that show compromised integrity, as they pose safety risks and are unlikely to perform as intended. Regular inspection is a proactive measure to maintain a safe working environment.

2. Proper Mounting:

Following manufacturer guidelines for mounting resin fiber discs is crucial. Ensure that the arbor size matches the disc and use appropriate mounting flanges. Improper mounting can lead to uneven wear, excessive vibration, and diminished efficiency. Properly mounted discs contribute to smoother operations and extended disc life.

3. Correct Grit Selection:

The selection of the appropriate grit size is fundamental to achieving desired results. Using a grit that is too coarse for finishing work or too fine for material removal can lead to suboptimal performance and unnecessary wear on the disc. Refer to guidelines and charts provided by manufacturers to make informed decisions based on the task at hand.

4. Maintaining Balanced Operations:

Imbalanced operations can have adverse effects on both the tool and the workpiece. Excessive vibration and premature wear on resin fiber discs can result from improper alignment of the workpiece, tool, and disc. Ensuring proper alignment promotes balanced and efficient performance, minimizing wear and tear on the disc.

5. Optimal Pressure and Speed:

Applying excessive pressure or operating at extremely high speeds can lead to overheating and premature wear of resin fiber discs. Adhering to manufacturer recommendations for pressure and speed settings is crucial. These recommendations are designed to deliver the best results while preserving the integrity of the disc and prolonging its operational life.

Conclusion:

As a key player in the realm of abrasive products, resin fiber discs, with their ability to deliver precision and efficiency, are indispensable tools in industries demanding high-performance abrasives. The careful consideration of storage and handling practices is essential for professionals seeking to maximize the efficiency and longevity of these discs. By implementing the guidelines outlined in this comprehensive guide, users can ensure that their resin fiber discs consistently deliver optimal results, maintain safety standards, and prove to be cost-effective tools in the long run. As industries continue to evolve, the emphasis on proper storage and handling practices becomes increasingly critical for those relying on resin fiber discs for their abrasive needs.

Drilling is a common task in various industries, from construction to mining and beyond. Whether you’re a professional tradesperson or a DIY enthusiast, you may encounter situations where a core bit gets stuck close to the surface during the drilling process. While this can be a frustrating and challenging problem, it’s essential to address it safely and effectively to avoid damage to your equipment and ensure a successful drilling operation. In this article, we will explore the common reasons for core bits getting stuck and provide step-by-step guidance on how to remove a stuck core bit close to the surface.

https://bsptools.com/wp-content/uploads/2023/11/1701399944928-350x233.png 350w, https://bsptools.com/wp-content/uploads/2023/11/1701399944928-165x110.png 165w, https://bsptools.com/wp-content/uploads/2023/11/1701399944928-24x16.png 24w, https://bsptools.com/wp-content/uploads/2023/11/1701399944928-36x24.png 36w, https://bsptools.com/wp-content/uploads/2023/11/1701399944928-48x32.png 48w" alt="CORE DRILL BIT" width="950" height="633" />

Core Drilling Process

Before delving into the removal techniques, it’s crucial to understand the core drilling process. Core drilling is a method used to create precise holes in various materials, including concrete, masonry, metal, and wood. A core drill consists of a hollow, cylindrical bit that removes a core or plug from the material being drilled. The core bit is attached to a drill rig or hand-held drill, and a motor provides the necessary rotational force for drilling.

Core bits can get stuck for several reasons, including:

• Jamming or Binding:If the material being drilled is too hard or dense, it can cause the core bit to jam or bind, making it difficult to remove.
• Inadequate Lubrication: Core drilling typically requires water or lubrication to cool the bit and flush away debris. If the lubrication is insufficient, it can lead to overheating and binding.
• Worn or Damaged Core Bit:A worn or damaged core bit may not cut effectively, causing it to get stuck during the drilling process.
• Incorrect Technique: Using the wrong drilling technique or applying excessive force can increase the chances of a core bit becoming stuck.

How to Remove a Stuck Core Bit Close to the Surface

Now, let’s explore the step-by-step process for removing a core bit stuck close to the surface.

Step 1: Safety First

Before attempting to remove a stuck core bit, it’s crucial to prioritize safety. Wear appropriate personal protective equipment, including safety glasses, gloves, and a dust mask. Make sure the drill is turned off and unplugged to prevent accidental activation during the removal process.

Step 2: Assess the Situation

Examine the core bit and the surrounding material to understand why it got stuck. If there are visible signs of binding or overheating, address these issues before attempting to remove the core bit.

Step 3: Lubricate the Core Bit

If insufficient lubrication was the problem, apply a suitable drilling lubricant or water to the core bit and the hole. Allow it to penetrate for a few minutes to reduce friction.

Step 4: Apply Tapping and Rotation

Tap the core bit gently with a hammer while applying rotational force. This can help break the bit loose from the material. Start with light taps and gradually increase the force if necessary. Continue tapping and rotating until you feel some movement.

Step 5: Reverse the Rotation

If tapping and rotation don’t yield results, try reversing the drill’s rotation. Sometimes, reversing the direction can help release the core bit from the material.

https://bsptools.com/wp-content/uploads/2023/11/图片-2-1-350x223.png 350w, https://bsptools.com/wp-content/uploads/2023/11/图片-2-1-165x105.png 165w, https://bsptools.com/wp-content/uploads/2023/11/图片-2-1-24x15.png 24w, https://bsptools.com/wp-content/uploads/2023/11/图片-2-1-36x23.png 36w, https://bsptools.com/wp-content/uploads/2023/11/图片-2-1-48x31.png 48w" alt="" width="960" height="613" />

Step 6: Use a Core Bit Puller

A core bit puller is a specialized tool designed to remove stuck core bits. It consists of a set of jaws that grip the core bit securely, allowing you to pull it out. Attach the core bit puller to the bit and use it to apply steady, even pressure while pulling the bit from the hole

Step 7: Apply Heat

In cases where the core bit is stuck due to a hardened material like concrete, heat can be used to soften the material and ease removal. A heat gun or propane torch can be applied to the area around the core bit. Heat the material, not the core bit, to avoid damaging it. After heating, attempt to remove the core bit using the tapping and rotation method or a core bit puller.

Step 8: Drilling a New Hole

If all else fails, and the core bit remains stuck, one last resort is to drill a new hole beside the stuck bit. This new hole should be large enough to expose the stuck core bit. Be careful not to damage the core bit while drilling the new hole. Once the core bit is exposed, try to remove it using the methods mentioned earlier.

Step 9: Seek Professional Help

If you’ve exhausted all the above methods and the core bit remains firmly stuck, it’s best to seek professional assistance. Attempting to force the bit out could lead to equipment damage or injury.

Preventive Measures

Preventing a core bit from getting stuck close to the surface is preferable to dealing with the problem afterward. Here are some preventive measures to consider:

1. Choose the Right Core Bit: Select the appropriate core bit for the material you are drilling. Different materials require specific core bit types to ensure efficient cutting.
2. Use Adequate Lubrication: Ensure proper lubrication during the drilling process. This cools the core bit and flushes away debris, reducing the chances of it getting stuck.
3. Follow Correct Drilling Techniques:Apply the correct drilling technique, which includes maintaining a consistent speed and avoiding excessive force.
4. Inspect and Maintain Equipment:Regularly inspect your core bits for wear and damage, and replace them as needed. Maintain your drilling equipment to ensure it operates smoothly.

Conclusion

Removing a stuck core bit close to the surface can be a challenging task, but with the right approach and safety measures, it’s manageable. Assess the situation, apply lubrication, use tapping and rotation, and consider specialized tools like core bit pullers. If all else fails, seek professional help to avoid potential damage to equipment and ensure your safety.

Remember that prevention is key. By choosing the right core bit, using proper lubrication, following correct drilling techniques, and maintaining your equipment, you can significantly reduce the likelihood of encountering a stuck core bit during your drilling operations.

Welding is a versatile and essential skill in various industries, from construction and automotive to metalworking and DIY projects. It involves joining pieces of metal together, creating strong and durable bonds. However, welding isn’t just about the act of joining; it also encompasses the preparation and finishing of welded joints. When it comes to finishing, choosing the right abrasive tools is crucial. One of the most popular options for finishing and grinding in welding is the flap disc. In this article, we will explore the different grits of flap discs and how to choose the right one for your metal welding projects.

What is a Flap Disc?

Before we dive into the details of choosing the right grit flap disc, let’s first understand what a flap disc is. A flap disc is an abrasive tool used for grinding, blending, and finishing metal surfaces. It consists of multiple overlapping, bonded abrasive flaps that are affixed to a backing plate. These abrasive flaps are typically made from aluminum oxide, zirconia alumina, or ceramic materials, which determine their cutting ability and durability.

Flap discs come in various sizes, with 4.5-inch and 7-inch diameters being common choices for welding applications. They are compatible with angle grinders and are easy to attach, making them a popular choice for welders and metalworkers. The key advantage of flap discs is their versatility; they can be used for a wide range of tasks, including removing rust, deburring, surface blending, and even polishing, all with a single tool.

Understanding Grit in Flap Discs

The term “grit” in the context of flap discs refers to the size of the abrasive particles on the disc. Grit size is a crucial factor to consider when choosing a flap disc for your welding projects, as it directly affects the disc’s cutting ability and finish quality. Grit sizes are denoted by numbers, and lower numbers indicate coarser grits, while higher numbers indicate finer grits.

Common Grit Ranges in Flap Discs

• Coarse Grits (24-60): Coarse grit flap discs are used for heavy material removal and aggressive grinding. They are suitable for tasks such as removing weld spatter, rough shaping, and deburring. The lower grit numbers, such as 24 or 36, are ideal for rapid material removal but leave a rough surface finish.
• Medium Grits (80-120): Medium grit flap discsstrike a balance between material removal and surface finish. They are great for preparing the metal surface before painting or applying coatings, as well as for general-purpose grinding and blending. Grits like 80 or 100 provide a smoother finish compared to coarser grits.
• Fine Grits (150-320): Fine grit flap discs are used for finishing and polishing. They are excellent for achieving a smooth, polished surface on metal and removing small imperfections left by coarser grits. These finer grits, such as 180 or 240, are often used for creating a smooth, paint-ready surface.

Choosing the Right Grit for Your Welding Projects

Selecting the appropriate grit flap disc is essential for achieving the desired finish and efficiency in your welding projects. The choice largely depends on the specific task at hand, the type of metal you’re working with, and your skill level. Here’s a breakdown of different welding tasks and the corresponding grits to use:

1. Weld Spatter Removal:

For rapid removal of weld spatter and rough shaping, use a coarse grit flap disc (24-36 grit).

After initial removal, switch to a medium grit flap disc (80-100 grit) to achieve a smoother surface.

2. Surface Blending and Preparation:

When blending the weld seams and preparing the metal surface for paint or coating, medium grit flap discs (80-120 grit) are your best choice.

Start with a coarser grit if the weld seams are pronounced and gradually move to finer grits for a smoother finish.

3. Deburring:

For removing sharp edges, burrs, and irregularities, medium grit flap discs (80-100 grit) are suitable.

In cases where you need a high-quality, burr-free finish, you can transition to fine grit flap discs (180-240 grit) for fine deburring.

4. Surface Finishing and Polishing:

If you aim to achieve a polished, mirror-like finish on your welded metal, fine grit flap discs (180-320 grit) are your go-to choice.

Use progressively finer grits to refine the surface and achieve the desired level of polish.

5. Paint Removal and Rust Removal:

For removing paint, rust, or coatings, start with a medium grit flap disc (80-100 grit) for efficient material removal.

If you need a smoother surface after removing paint or rust, consider using a finer grit flap disc (180-240 grit).

Tips for Effective Flap Disc Use

To maximize the performance and lifespan of your flap discs in welding projects, consider the following tips:

1. Safety First: Always wear appropriate personal protective equipment, including safety glasses, a dust mask, and hearing protection, when using flap discs.
2. Choose the Right RPM:Ensure that your angle grinder is set to the recommended RPM (Revolutions Per Minute) for the specific flap disc you are using.
3. Maintain Consistent Pressure: Apply even and consistent pressure to the flap disc to prevent uneven wear and gouging.
4. Use the Right Angle: Hold the angle grinder at the appropriate angle for the task at hand. Typically, a 15-20-degree angle to the workpiece is recommended.
5. Keep the Disc Flat: Maintain a flat and level angle between the flap disc and the workpiece to avoid digging in or gouging.
6. Work in Stages: If your project requires a smooth finish, work in stages, starting with a coarser grit and progressing to finer grits.
7. Keep the Disc Clean: Periodically clean the flap disc by tapping it against a hard surface to remove accumulated debris.

Conclusion

In welding projects, selecting the right grit flap disc is crucial for achieving the desired finish, whether it’s removing weld spatter, preparing surfaces for paint, or achieving a polished look. Understanding the various grit ranges and their applications is key to making the right choice for your specific welding task. By following the tips for effective flap disc use, you can maximize the performance and longevity of these versatile tools. So, the next time you tackle a welding project, be sure to choose the appropriate grit flap disc to get the job done efficiently and effectively.

Jesus died as a sacrificial lamb and rose again. He made a way for us to avoid the second death spoken about in Revelation. When He calls the church home, these mortal bodies will be transformed to immortal ones. Click on the link below to read more about living forever. #BibleStudy #Devotions #Evangelism #Genesis

https://www.ramckinley.com/death-is-defeated/

Greetings in The Mighty Name of Jesus, The Christ!!!

Blessings Upon Blessings

Brothers and Sisters we are a Blessed People that goes beyond understanding. For if you Look in depth to all the things that are in this World, they go beyond What was Created to a depth that even a Microscope cannot see. Man may say that we Know the Depths of what we see, but I would call all liars.

So how do we as Born Again, Blood Bought, know this? There are two ways, one because The Father said so and secondly man’s Understanding Of Creation is limited to What The Father has Allowed Us To Find. Man wants things bigger, faster and better but cannot see past the end of our noses. There are many, many things that are in this World that we do not understand. Yet Man…wants to be God!

Isaiah 55:8-9 KJV

"⁸ For my thoughts [are] not your thoughts, neither [are] your ways my ways, saith the LORD. ⁹ For [as] the heavens are higher than the earth, so are my ways higher than your ways, and my thoughts than your thoughts."

For Our Understanding we cannot understand how in the first place that The Father Created the Heavens and Earth out of NOTHING, nor can we even come close to how The Father Created Man from Dust or even how The Fathers Breath made a Living Soul. But in these things we are Blessed beyond measure literally!

I want you to take just 5 minutes, look around your environment that you are currently in, start in one place and think of The Depth Of Creation all the way down to nothing, I will guarantee you cannot get past 1. We, mankind take The Fathers Creation for granite not truly understanding the Blessings that He has given us. Man may say “I Made This…”, but who Made the Beginning? Who Gave the Knowledge, Understanding and Wisdom, but only in a fraction for us to be able to Create anything?

There are Blessings that we can Obtain that go beyond the Lost, beyond the Heathen, beyond God’s Enemies, but there is a Clause. Consider the following Scriptures…

Deuteronomy 28:1-10 KJV

"¹ And it shall come to pass, if thou shalt hearken diligently unto the voice of the LORD thy God, to observe [and] to do all his commandments which I command thee this day, that the LORD thy God will set thee on high above all nations of the earth: ² And all these blessings shall come on thee, and overtake thee, if thou shalt hearken unto the voice of the LORD thy God. ³ Blessed [shalt] thou [be] in the city, and blessed [shalt] thou [be] in the field. ⁴ Blessed [shall be] the fruit of thy body, and the fruit of thy ground, and the fruit of thy cattle, the increase of thy kine, and the flocks of thy sheep. ⁵ Blessed [shall be] thy basket and thy store. ⁶ Blessed [shalt] thou [be] when thou comest in, and blessed [shalt] thou [be] when thou goest out. ⁷ The LORD shall cause thine enemies that rise up against thee to be smitten before thy face: they shall come out against thee one way, and flee before thee seven ways. ⁸ The LORD shall command the blessing upon thee in thy storehouses, and in all that thou settest thine hand unto; and he shall bless thee in the land which the LORD thy God giveth thee. ⁹ The LORD shall establish thee an holy people unto himself, as he hath sworn unto thee, if thou shalt keep the commandments of the LORD thy God, and walk in his ways. ¹⁰ And all people of the earth shall see that thou art called by the name of the LORD; and they shall be afraid of thee."

This is a Blessing that The Father gave to the Hebrews, to Israel that we also have been made heirs with them can obtain as well, as long as we abide by The Clause that The Father put in. The Clause is the following, “hearken diligently unto the voice of the Lord they God” this is the First Clause. The Second Clause is this…, “to observe and to do all his commandments”. Many, many of you Pray and Pray and Pray but it is for selfish gain and receive No Blessing, because you do not even do the First Clause. You do not truly Seek Jesus, but think you can use Jesus as a gene in a bottle.

The above Scriptures start with the Clause and ends with the same Clauses with the Blessings between the Clauses. If the Clauses are Broken, if they are Not Followed, then the Blessings will not come, they will not happen no matter how much you beg and plea with Jesus.

Some will say, “Well that was in the Old Testament, it is different in the New Testament because we are Under Grace…”. Has Jesus not said the same thing…?

John 14:15 KJV

“If ye love me, keep my commandments."

Philippians 4:19-20 KJV

"¹⁹ But my God shall supply all your need according to his riches in glory by Christ Jesus. ²⁰ Now unto God and our Father [be] glory for ever and ever. Amen."

Matthew 5:3-12 KJV

"³ Blessed [are] the poor in spirit: for theirs is the kingdom of heaven. ⁴ Blessed [are] they that mourn: for they shall be comforted. ⁵ Blessed [are] the meek: for they shall inherit the earth. ⁶ Blessed [are] they which do hunger and thirst after righteousness: for they shall be filled. ⁷ Blessed [are] the merciful: for they shall obtain mercy. ⁸ Blessed [are] the pure in heart: for they shall see God. ⁹ Blessed [are] the peacemakers: for they shall be called the children of God. ¹⁰ Blessed [are] they which are persecuted for righteousness' sake: for theirs is the kingdom of heaven. ¹¹ Blessed are ye, when [men] shall revile you, and persecute [you], and shall say all manner of evil against you falsely, for my sake. ¹² Rejoice, and be exceeding glad: for great [is] your reward in heaven: for so persecuted they the prophets which were before you."

I have so many Blessings through the years that I literally cannot count them all, but it is not because I am Perfect In The Will Of God, but it is that I SEEK Jesus and His Will, which is the same Will As The Father, for MY WHOLE LIFE and then I try to Walk In Obedience to that Will, with Grace Abound!

I can name some that you may not think of. I thank Jesus when I see a beautiful Sun Rise or Sun Set for it is a Blessings of The Fathers that I Can See. I thank Jesus when I am fishing and I look around at the Natural Landscape, for I am Blessed in Standing in the midst of The Fathers Creation. I am Blessed every time that I catch a fish, both great and small and I thank Jesus. I am Blessed when it is a hot day and in the midst of my labor, a small breeze comes along and refreshes me. This is only the micro tip of my Blessings. I Look for my Blessings by the hour!

For me, I can see Blessings in both Life and Death in that I am Blessed in the Direction, Guidance, Wisdom, Knowledge and Understanding that The Holy Spirit gives me through Jesus MY LORD!!!

Many of you have cursed your own Life because you “Say” you Believe, but do you really? If your Belief does not involve you Walking In Obedience, then you have No Blessings From Jesus, not even Eternal Life! Throughout the Old Testament and into the New Testament we find that Blessings are Accompanied by Obedience, for the two Walk Hand In Hand together as one. But, you cannot just Do what Jesus says and expect to be Blessed, it does not work that way. But it takes a Relationship, a Bond between You and Jesus for Blessings to occur.

Matthew 22:37-40 KJV

"³⁷  Jesus said unto him, Thou shalt love the Lord thy God with all thy heart, and with all thy soul, and with all thy mind. ³⁸ This is the first and great commandment. ³⁹ And the second [is] like unto it, Thou shalt love thy neighbour as thyself. ⁴⁰ On these two commandments hang all the law and the prophets."

Luke 10:27 KJV

“And he answering said, Thou shalt love the Lord thy God with all thy heart, and with all thy soul, and with all thy strength, and with all thy mind; and thy neighbour as thyself."

The Father and Jesus, REQUIRES, DEMANDS, that in order for Blessings to come, then Obedience MUST Come First!!! Now, with that being said, yes, there are times that Blessings come without obedience, but in all cases they are to Draw that person into a Relationship With Jesus and it may only be a onetime deal or it can be multiple. Doubting Thomas had to be Proven To that it was Jesus who stood before him by touching His Wounds.

John 20:27 KJV

“Then saith he to Thomas, Reach hither thy finger, and behold my hands; and reach hither thy hand, and thrust [it] into my side: and be not faithless, but believing."

Brothers and Sisters if you Want a Blessing, if you Need a Blessing then you Must First walk in Obedience to the Voice Of Our Lord Jesus. Thomas did not Receive the Blessing of Eternity until he first Obeyed the Voice Of Jesus To Do something first. Many Seek Answers, but Jesus says Seek Me First Not The Answer First.

The Father or Jesus or The Holy Spirit has not changed the Rules Of Blessings. They have not Added To the rules nor have they taken any away. Blessings are for us, but we MUST Seek and Obey Jesus First, even as Jesus did His Father, that is, Jesus Sought and Did only The Fathers Will With His Entire Life, even unto Death on the cross.

Hebrews 13:8 KJV

“Jesus Christ the same yesterday, and to day, and for ever."

 Matthew 7:21 KJV

“Not every one that saith unto me, Lord, Lord, shall enter into the kingdom of heaven; but he that doeth the will of my Father which is in heaven."

John 5:30 KJV

“I can of mine own self do nothing: as I hear, I judge: and my judgment is just; because I seek not mine own will, but the will of the Father which hath sent me."

When you put Jesus First in your Entire Life, you will see Blessings Upon Blessings in Your Life!!! Even as Moses has said, so do I to you… Choosing is Your Free Will, that will determine Blessings or Cursing… Chose Today!

1 John 4:17 KJV

“Herein is our love made perfect, that we may have boldness in the day of judgment: because as he is, so are we in this world."

Deuteronomy 11:26-28 KJV

"²⁶ Behold, I set before you this day a blessing and a curse; ²⁷ A blessing, if ye obey the commandments of the LORD your God, which I command you this day: ²⁸ And a curse, if ye will not obey the commandments of the LORD your God, but turn aside out of the way which I command you this day, to go after other gods, which ye have not known."

Amen and Amen!!!

Email: godsonlyfoundation@gmail.com

Website: ApostleLee.com

The Apostle Paul needed to deal with some false teaching among the Galatians. He considered what they taught as foolishness because they were adding requirements to some people for them to receive salvation. But the apostle made it quite clear that God looked at everyone equally. Click on the link below to read what this was all about. #316 #BibleStudy #Devotions #Galatians

https://www.ramckinley.com/how-to-receive-a-great-inheritance-in-the-lord/

Drilling is a common task in various industries, from construction to mining and beyond. Whether you’re a professional tradesperson or a DIY enthusiast, you may encounter situations where a core bit gets stuck close to the surface during the drilling process. While this can be a frustrating and challenging problem, it’s essential to address it safely and effectively to avoid damage to your equipment and ensure a successful drilling operation. In this article, we will explore the common reasons for core bits getting stuck and provide step-by-step guidance on how to remove a stuck core bit close to the surface.

https://bsptools.com/wp-content/uploads/2023/11/图片-2-1-350x223.png 350w, https://bsptools.com/wp-content/uploads/2023/11/图片-2-1-165x105.png 165w, https://bsptools.com/wp-content/uploads/2023/11/图片-2-1-24x15.png 24w, https://bsptools.com/wp-content/uploads/2023/11/图片-2-1-36x23.png 36w, https://bsptools.com/wp-content/uploads/2023/11/图片-2-1-48x31.png 48w" alt="" width="977" height="624" />

Core Drilling Process

Before delving into the removal techniques, it’s crucial to understand the core drilling process. Core drilling is a method used to create precise holes in various materials, including concrete, masonry, metal, and wood. A core drill consists of a hollow, cylindrical bit that removes a core or plug from the material being drilled. The core bit is attached to a drill rig or hand-held drill, and a motor provides the necessary rotational force for drilling.

Core bits can get stuck for several reasons, including:

• Jamming or Binding:If the material being drilled is too hard or dense, it can cause the core bit to jam or bind, making it difficult to remove.
• Inadequate Lubrication: Core drilling typically requires water or lubrication to cool the bit and flush away debris. If the lubrication is insufficient, it can lead to overheating and binding.
• Worn or Damaged Core Bit:A worn or damaged core bit may not cut effectively, causing it to get stuck during the drilling process.
• Incorrect Technique: Using the wrong drilling technique or applying excessive force can increase the chances of a core bit becoming stuck.

How to Remove a Stuck Core Bit Close to the Surface

Now, let’s explore the step-by-step process for removing a core bit stuck close to the surface.

Step 1: Safety First

Before attempting to remove a stuck core bit, it’s crucial to prioritize safety. Wear appropriate personal protective equipment, including safety glasses, gloves, and a dust mask. Make sure the drill is turned off and unplugged to prevent accidental activation during the removal process.

Step 2: Assess the Situation

Examine the core bit and the surrounding material to understand why it got stuck. If there are visible signs of binding or overheating, address these issues before attempting to remove the core bit.

Step 3: Lubricate the Core Bit

If insufficient lubrication was the problem, apply a suitable drilling lubricant or water to the core bit and the hole. Allow it to penetrate for a few minutes to reduce friction.

Step 4: Apply Tapping and Rotation

Tap the core bit gently with a hammer while applying rotational force. This can help break the bit loose from the material. Start with light taps and gradually increase the force if necessary. Continue tapping and rotating until you feel some movement.

Step 5: Reverse the Rotation

If tapping and rotation don’t yield results, try reversing the drill’s rotation. Sometimes, reversing the direction can help release the core bit from the material.

Step 6: Use a Core Bit Puller

A core bit puller is a specialized tool designed to remove stuck core bits. It consists of a set of jaws that grip the core bit securely, allowing you to pull it out. Attach the core bit puller to the bit and use it to apply steady, even pressure while pulling the bit from the hole

Step 7: Apply Heat

In cases where the core bit is stuck due to a hardened material like concrete, heat can be used to soften the material and ease removal. A heat gun or propane torch can be applied to the area around the core bit. Heat the material, not the core bit, to avoid damaging it. After heating, attempt to remove the core bit using the tapping and rotation method or a core bit puller.

Step 8: Drilling a New Hole

If all else fails, and the core bit remains stuck, one last resort is to drill a new hole beside the stuck bit. This new hole should be large enough to expose the stuck core bit. Be careful not to damage the core bit while drilling the new hole. Once the core bit is exposed, try to remove it using the methods mentioned earlier.

Step 9: Seek Professional Help

If you’ve exhausted all the above methods and the core bit remains firmly stuck, it’s best to seek professional assistance. Attempting to force the bit out could lead to equipment damage or injury.

https://bsptools.com/wp-content/uploads/2023/11/图片-1-1-350x233.png 350w, https://bsptools.com/wp-content/uploads/2023/11/图片-1-1-165x110.png 165w, https://bsptools.com/wp-content/uploads/2023/11/图片-1-1-24x16.png 24w, https://bsptools.com/wp-content/uploads/2023/11/图片-1-1-36x24.png 36w, https://bsptools.com/wp-content/uploads/2023/11/图片-1-1-48x32.png 48w" alt="" width="977" height="651" />

Preventive Measures

Preventing a core bit from getting stuck close to the surface is preferable to dealing with the problem afterward. Here are some preventive measures to consider:

1. Choose the Right Core Bit: Select the appropriate core bit for the material you are drilling. Different materials require specific core bit types to ensure efficient cutting.
2. Use Adequate Lubrication: Ensure proper lubrication during the drilling process. This cools the core bit and flushes away debris, reducing the chances of it getting stuck.
3. Follow Correct Drilling Techniques:Apply the correct drilling technique, which includes maintaining a consistent speed and avoiding excessive force.
4. Inspect and Maintain Equipment:Regularly inspect your core bits for wear and damage, and replace them as needed. Maintain your drilling equipment to ensure it operates smoothly.

Conclusion

Removing a stuck core bit close to the surface can be a challenging task, but with the right approach and safety measures, it’s manageable. Assess the situation, apply lubrication, use tapping and rotation, and consider specialized tools like core bit pullers. If all else fails, seek professional help to avoid potential damage to equipment and ensure your safety.

​

Remember that prevention is key. By choosing the right core bit, using proper lubrication, following correct drilling techniques, and maintaining your equipment, you can significantly reduce the likelihood of encountering a stuck core bit during your drilling operations.

Abrasives are indispensable tools in various industries, facilitating the shaping, finishing, and polishing of materials through grinding, cutting, or sanding processes. Among the diverse types of abrasives, understanding the nuances between bonded, coated, and non-woven abrasives is essential for selecting the most suitable tool for specific applications.

Bonded Abrasives

Bonded abrasives, recognized for their durability and versatility, consist of abrasive grains bound together by materials such as vitrified clay, resin, or rubber. This bonding material ensures controlled material removal in a variety of applications.

Types of Bonded Abrasives

1. Grinding Wheels:Circular wheels with embedded abrasive grains, grinding wheels are instrumental in precision grinding operations common in metal fabrication and manufacturing.
2. Mounted Points:Small, specialized abrasive tools mounted on spindles, these are ideal for intricate grinding operations, particularly in hard-to-reach areas.
3. Segments: Blocks of abrasive material held together by a bonding agent, segments are frequently used in surface grinding applications to efficiently remove material from large surfaces.
4. Cut-Off Wheels:These are thin, rigid wheels designed for cutting various materials, making them essential in metalworking and construction.

How Bonded Abrasives Are Made

Manufacturing bonded abrasives involves mixing abrasive grains with bonding agents, shaping the mixture into the desired form (such as wheels or segments), and then curing or baking the product to harden the bonding material.

How Bonded Abrasives Work

Bonded abrasives work by utilizing the abrasive grains to remove material from the workpiece through cutting, grinding, or finishing processes. The bonding material holds the grains in place, ensuring precision and control during the operation.

Benefits and Limitations of Bonded Abrasives

Benefits:

• Durability:Bonded abrasives are known for their robustness, making them suitable for heavy-duty applications.
• Precision:They offer precise control over material removal, making them ideal for applications requiring accuracy.
• Versatility: Bonded abrasives can be used on a variety of materials, including metal, ceramics, and composites.

Limitations:

• Heat Generation:In heavy use, bonded abrasives can generate heat, requiring careful consideration to prevent damage to the workpiece.
• Initial Cost:The upfront cost of bonded abrasives can be higher than other types, but their durability often justifies the investment.

Coated Abrasives

Coated abrasives, featuring abrasive grains on a flexible backing material, are valued for their versatility and conformability. This flexibility makes them suitable for applications where a more adaptable abrasive is necessary.

Types of Coated Abrasives

1. Sandpaper:A familiar form of coated abrasives, sandpaper consists of abrasive grains adhered to paper or cloth backing. It is widely used for hand sanding and power tool applications.
2. Abrasive Belts:Continuous loops of coated abrasive material used in belt sanders, these belts are efficient for large surface areas and are common in woodworking and metalworking.
3. Flap Discs:These discs feature overlapping flaps of coated abrasive material attached to a central hub, making them effective for blending and finishing applications in metal fabrication.

How Coated Abrasives Are Made

The production of coated abrasives involves applying adhesive to a flexible backing material and then embedding abrasive grains into the adhesive. The coated product is then cured or dried, creating a flexible yet durable abrasive tool.

How Coated Abrasives Work

Coated abrasives work by allowing the abrasive grains to abrade the material as the flexible backing conforms to the surface. This conformability makes coated abrasives ideal for contoured or irregular surfaces.

Benefits and Limitations of Coated Abrasives

Benefits:

• Flexibility: Coated abrasives are flexible and conformable, making them suitable for irregular surfaces and contours.
• Versatility: They can be used for a wide range of applications, from hand sanding to automated machinery.
• Efficient Material Removal:Coated abrasives are effective for material removal and surface finishing.

Limitations:

• Wear Rate:Coated abrasives may experience a higher wear rate compared to bonded abrasives, requiring more frequent replacements.
• Heat Buildup: In heavy use, coated abrasives can generate heat, necessitating periodic breaks to prevent overheating.

Non-Woven Abrasives

Non-woven abrasives, characterized by a three-dimensional web of nylon fibers impregnated with abrasive grains, offer a unique cutting action that ensures consistency and precision.

Types of Non-Woven Abrasives

1. Hand Pads: Versatile tools for cleaning, deburring, and finishing surfaces, non-woven hand pads find applications in metalworking and woodworking.
2. Belts: Ideal for applications requiring conformability, non-woven abrasive beltsare used for blending and finishing on curved or contoured surfaces.
3. Discs and Wheels: Used for surface preparation and finishing tasks, non-woven abrasive discsand wheels come in various diameters and densities to suit different applications.

How Non-Woven Abrasives Are Made

Manufacturing non-woven abrasives involves bonding abrasive grains to a three-dimensional nylon web. The impregnation process ensures a consistent distribution of abrasive material, creating a tool with controlled cutting action.

How Non-Woven Abrasives Work

Non-woven abrasives work by allowing the nylon fibers to conform to the surface, while the embedded abrasive grains perform the cutting action. This unique structure results in a consistent finish without the risk of gouging or marring the workpiece.

Benefits and Limitations of Non-Woven Abrasives

Benefits:

• Consistent Finish: Non-woven abrasives provide a consistent finish without the risk of gouging or marring the workpiece.
• Cooler Operation: The open structure of non-woven abrasives allows for cooler operation, reducing the risk of heat-related damage to the workpiece.
• Versatility:Non-woven abrasives are effective on a wide range of materials, including metal, wood, and composites.

Limitations:

• Material Removal Rate: Non-woven abrasives may have a slower material removal rate compared to some bonded and coated abrasives.
• Initial Cost: While cost-effective in the long run, non-woven abrasives may have a higher initial cost.

Choosing the Right Abrasive

Selecting the appropriate abrasive involves considering the material type, application, tool compatibility, and surface finish requirements. Bonded abrasives are ideal for precision work, coated abrasives for flexibility, and non-woven abrasives for consistent finishing. Each type has its unique characteristics, advantages, and applications, and choosing wisely can lead to improved efficiency, precision, and overall success in various industries.

Abrasives have been a crucial part of various industries, from woodworking to automotive and even in the realm of DIY projects. Sanding, in particular, is a common and essential process that can transform rough surfaces into smooth, polished ones. One of the key innovations in the sanding industry has been the introduction of Velcro sanding discs. These discs, with their ease of use and versatility, have revolutionized the way we approach sanding tasks. In this article, we will delve into the world of abrasive Velcro sanding discs, exploring the reasons behind their popularity and how they have become indispensable tools for professionals and hobbyists alike.

The Evolution of Sanding

Sanding, in its simplest form, involves the removal of material from a surface through the abrasive action of a sandpaper or abrasive material. This process has a long history, dating back to ancient times when sand and primitive abrasive materials were used. The goal has always been to achieve a smoother and more refined surface, whether it’s wood, metal, or even plastic.

The traditional method of attaching sandpaper to a sanding block or machine involved adhesives or clips. While this method worked, it had its drawbacks. Adhesive-based sandpaper was prone to peeling, tearing, and could leave behind sticky residue. Clips were effective but not always easy to work with, especially when changing sandpaper frequently. This is where Velcro sanding discs came into play.

The Advantages of Velcro Sanding Discs

Ease of Use: Velcro sanding discs have gained immense popularity due to their user-friendly design. Their hook-and-loop system eliminates the need for adhesives or complicated clips, making it incredibly easy to attach and remove sandpaper. This feature not only saves time but also reduces frustration, making sanding a more enjoyable process.

1. Quick and Easy Grit Changes:Abrasive Velcro sanding discs come in various grits, ranging from coarse to fine. When a project demands different levels of abrasiveness, users can effortlessly switch between discs, allowing for a seamless transition between sanding stages. This ability to change grits on the fly is particularly valuable for professionals working on multi-stage projects.
2. Cost-Efficiency: While the initial investment in a Velcro sanding disc setup might be slightly higher than traditional sanding methods, the cost-efficiency becomes evident over time. The hook-and-loop system prolongs the life of sandpaper by reducing wear and tear during changes, ultimately saving money in the long run.
3. Improved Dust Management:Many Velcro sanding discs come with perforations that allow for efficient dust extraction. This means a cleaner work environment, better visibility of the surface being sanded, and reduced health risks associated with inhaling dust particles. Proper dust extraction is crucial for both safety and the quality of the finished product.
4. Versatility Across Materials: Velcro sanding discs can be used on a wide range of materials, including wood, metal, plastic, and even automotive finishes. Their adaptability makes them a go-to choice for professionals and DIY enthusiasts working on a variety of projects.
5. Reduced Surface Damage: The Velcro system ensures that the sandpaper remains securely attached, reducing the likelihood of surface damage caused by sandpaper detachment or slippage. This can be especially important when working on delicate or high-value materials.

Applications of Abrasive Velcro Sanding Discs

• Woodworking:Woodworkers often rely on Velcro sanding discs to achieve the smooth, polished finish that’s essential for fine woodworking projects. The quick grit changes and dust extraction capabilities make these discs ideal for preparing surfaces, removing imperfections, and finishing details on wooden pieces.

• Automotive Refinishing:In the automotive industry, Velcro sanding discs are indispensable for prepping and refinishing paint surfaces. Their ability to adapt to the contours of a vehicle, combined with effective dust extraction, ensures that the final finish is not marred by imperfections.
• Metalworking: Metalworkers use Velcro sanding discs to shape and polish metal surfaces. These discs can handle the rougher tasks of removing rust, paint, or burrs, as well as the more delicate work of achieving a mirror-like finish on metals.
• Drywall Sanding:When it comes to drywall work, Velcro sanding discs are highly efficient in reducing the time and effort required for smoothing joint compounds and sanding seams. The dust extraction feature is especially appreciated in indoor projects, where airborne dust can be a nuisance.
• DIY and Home Improvement: DIY enthusiasts find Velcro sanding discs particularly handy for a wide range of projects, from refinishing furniture to sanding surfaces for painting. The ease of use and ability to switch between grits make these discs suitable for small and large-scale home improvement projects.

Conclusion

Abrasives, particularly Velcro sanding discs, have revolutionized the way we approach sanding tasks across various industries and DIY projects. The Velcro sanding disc’s ease of use, cost-efficiency, quick grit changes, dust extraction capabilities, and versatility across materials have made them a staple tool for professionals and hobbyists alike. Their ability to streamline the sanding process, reduce surface damage, and enhance the quality of finished products has made them an invaluable innovation in the world of abrasives. Whether you’re a professional craftsman or a weekend warrior, the adoption of Velcro sanding discs can significantly improve the quality and efficiency of your work.

Porcelain tiles have become a popular choice for flooring and wall applications due to their durability, aesthetic appeal, and resistance to water and stains. However, cutting through these dense and hard tiles requires specialized tools and blades. In this article, we will delve into the characteristics of porcelain tiles and explore the various types of blades available for cutting them, helping you make an informed decision on the best blade for your specific needs.

https://bsptools.com/wp-content/uploads/2023/11/图片-2-350x233.png 350w, https://bsptools.com/wp-content/uploads/2023/11/图片-2-165x110.png 165w, https://bsptools.com/wp-content/uploads/2023/11/图片-2-24x16.png 24w, https://bsptools.com/wp-content/uploads/2023/11/图片-2-36x24.png 36w, https://bsptools.com/wp-content/uploads/2023/11/图片-2-48x32.png 48w" alt="" width="960" height="640" />

Understanding Porcelain Tiles:

Porcelain tiles are made from a mixture of fine clay and other materials that are fired at high temperatures, resulting in a dense and hard material. This composition gives porcelain tiles their unique properties, including resistance to moisture, durability, and a smooth, polished finish. Cutting through porcelain tiles demands precision and the right tools to avoid chipping or cracking.

Factors to Consider When Choosing a Porcelain Tile Blade:

1. Diamond Blades:

The most effective blades for cutting porcelain tiles are those embedded with diamonds. Diamond blades are renowned for their hardness and ability to cut through tough materials. The diamonds on the blade’s edge are what enable it to grind through the hard surface of porcelain tiles.

2. Continuous Rim vs. Segmented Rim:

Diamond blades come in two main types: continuous rim and segmented rim. Continuous rim blades have a smooth, continuous edge, providing a cleaner and smoother cut. They are ideal for making precision cuts, such as when creating notches or curves. Segmented rim blades, on the other hand, have gaps between the diamond segments, allowing for faster cutting through tough materials. They are suitable for straight cuts but may leave a rougher edge compared to continuous rim blades.

3. Blade Size:

The size of the blade is another crucial factor. Blades come in various diameters, and the right size depends on the size of the porcelain tiles and the type of cut you need. Smaller blades are suitable for intricate cuts, while larger blades are better for straight cuts on larger tiles.

4. Wet vs. Dry Cutting:

Diamond blades can be used for both wet and dry cutting. Wet cutting involves using water to cool the blade and reduce dust. This method is preferable for larger projects as it helps prevent overheating and prolongs the life of the blade. Dry cutting, on the other hand, is quicker and more convenient for smaller projects but may generate more dust, necessitating proper safety measures.

5. Hardness of Porcelain:

The hardness of the porcelain tile itself is a critical factor in blade selection. If you are working with particularly hard porcelain, a blade with a higher concentration of diamonds may be necessary to ensure efficient cutting.

Types of Diamond Blades for Porcelain Tiles:

https://bsptools.com/wp-content/uploads/2023/11/图片-1-350x232.png 350w, https://bsptools.com/wp-content/uploads/2023/11/图片-1-165x109.png 165w, https://bsptools.com/wp-content/uploads/2023/11/图片-1-24x16.png 24w, https://bsptools.com/wp-content/uploads/2023/11/图片-1-36x24.png 36w, https://bsptools.com/wp-content/uploads/2023/11/图片-1-48x32.png 48w" alt="" width="960" height="636" />

• Turbo Rim Diamond Blades:

Turbo rim blades are designed for fast and aggressive cutting. They have a serrated rim that allows for quick material removal. These blades are suitable for both wet and dry cutting and are effective for straight cuts on porcelain tiles.

• Sintered Diamond Blades:

Sintered diamond blades are made by blending diamonds with metal powders and then sintering them at high temperatures. This process results in a blade with a high diamond concentration, making it suitable for cutting hard materials like porcelain. Sintered blades are known for their durability and longevity.

• Electroplated Diamond Blades:

Electroplated blades have a single layer of diamonds attached to the blade using a nickel plating process. While these blades are not as durable as sintered blades, they are highly effective for cutting softer porcelain tiles. They are also more affordable, making them a suitable choice for occasional use.

• Continuous Rim Diamond Blades:

As mentioned earlier, continuous rim blades provide a smooth and clean cut. They are ideal for precise cutting tasks, such as creating curves or notches in porcelain tiles. These blades work well for wet cutting applications.

Tips for Cutting Porcelain Tiles:

1. Mark Your Cut Lines:

Before cutting, use a pencil or marker to mark the cut lines on the surface of the tile. This ensures accuracy and helps prevent mistakes.

2. Secure the Tile:

To prevent the tile from shifting during the cutting process, secure it firmly in place using clamps or another suitable method.

3. Wear Safety Gear:

Whether you choose wet or dry cutting, porcelain tile cutting generates dust and debris. To protect yourself, wear safety glasses, a dust mask, and ear protection.

4. Choose the Right Speed:

Adjust the speed of your saw or cutting tool according to the blade’s specifications and the hardness of the porcelain. Using the correct speed helps optimize cutting performance and blade life.

Conclusion:

Selecting the best blade for cutting porcelain tiles involves considering factors such as blade type, rim design, size, and the hardness of the porcelain itself. Each type of blade has its advantages and is suitable for specific applications. Whether you opt for a turbo rim, sintered, or electroplated diamond blade, ensuring that it matches your project’s requirements will result in clean, precise cuts without compromising the integrity of the porcelain tiles. By understanding these factors and following the recommended tips, you can confidently choose the ideal blade for your porcelain tile cutting needs.

Paul and Barnabas went to the synagogue for a regular service in Antioch of Pisidia. While there, God opened the door for them to share the good news of the gospel. Paul used a very effective method when he shared the gospel. Click on the link below to read how he did it. #Acts #BibleStudy #Devotions #worship

https://www.ramckinley.com/rely-on-the-god-of-grace/

What is a Tote Bag?

Greetings in The Mighty Name of Jesus, The Christ!!!

Sin The Great Deceiver

Many, many Believers, Blood Bought, Saved weigh Sin in Magnitude by Their Understanding, Not Gods (The Father, Jesus, Holy Spirit). Man looks at Sin and within himself, will Declare that’s not so bad or that is the worst. Many, many Believers, Blood Bought, Saved, think that once they have Accepted Jesus as Savior that from that day forward everything is Washed Away By The Blood Of Jesus, that they can do No Wrong, Never be Lost Again. These are all Lies, Deceptions, Manipulations that both Satan and Man have come up with, but The Scriptures and The Holy Spirit say different, most of all, Jesus says different.

What was the Great Fall of Mankind? The Father told Adam, not Eve, not to Eat from the Tree Of Knowledge and that if he did, he would die.

Genesis 2:9, 17 KJV

"⁹ And out of the ground made the LORD God to grow every tree that is pleasant to the sight, and good for food; the tree of life also in the midst of the garden, and the tree of knowledge of good and evil. ... ¹⁷ But of the tree of the knowledge of good and evil, thou shalt not eat of it: for in the day that thou eatest thereof thou shalt surely die."

There was No Time Frame on this Command from The Father, it was an Absolute, no if’s, no buts, no maybe’s, no excuses, “Adam if you eat from this Tree and You will die”!

Eve, who was Tricked by Satan, because of the Lust Of The Eye, did eat the Forbidden Fruit First, then went and gave Adam the same Forbidden Fruit believing her over The Father. For Eve after she had eaten the Forbidden Fruit was very much alive, was not dead as The Father said would happen, so being seduced by Eve to eat, Adam at the very first bit, Disobeyed The Father.

At this time neither Adam or Eve understood the Consequences of their actions, for IN Their Eyes they both were still Alive and did not Die. Adam’s Action condemned them and all of mankind into a Sinful Nature…through DNA. But there was a Great Separation between Adam and The Father now, in so much that the Perfect Environment that The Father had prepared for Adam and Eve, were now being Cast Out, Thrown Out, could Never Return into that Place of Fellowship with The Father. It was a Spiritual Separation because of Sin, because of Disobedience.

Genesis 3:23-24 KJV

"²³ Therefore the LORD God sent him forth from the garden of Eden, to till the ground from whence he was taken. ²⁴ So he drove out the man; and he placed at the east of the garden of Eden Cherubims, and a flaming sword which turned every way, to keep the way of the tree of life."

Moving on…

A Young Prophet was given an assignment from The Father with Specific Instruction. The Young Prophet started his journey and along the way ran into an Old Prophet…

1 Kings 13:8-10 KJV

"⁸ And the man of God said unto the king, If thou wilt give me half thine house, I will not go in with thee, neither will I eat bread nor drink water in this place: ⁹ For so was it charged me by the word of the LORD, saying, Eat no bread, nor drink water, nor turn again by the same way that thou camest. ¹⁰ So he went another way, and returned not by the way that he came to Bethel."

This Man Of God was told by The Father that he was not to Eat Bread, not to Drink Water and not to Walk In the Same Path as he had already walked, this, the Man Of God quoted to the King and the Man Of God Obeyed The Father and went out of Bethel a different direction.

But here comes the Deception, the Deceiver…

1 Kings 13:11, 14-19 KJV

"¹¹ Now there dwelt an old prophet in Bethel; and his sons came and told him all the works that the man of God had done that day in Bethel: the words which he had spoken unto the king, them they told also to their father. ... ¹⁴ And went after the man of God, and found him sitting under an oak: and he said unto him, [Art] thou the man of God that camest from Judah? And he said, I [am]. ¹⁵ Then he said unto him, Come home with me, and eat bread. ¹⁶ And he said, I may not return with thee, nor go in with thee: neither will I eat bread nor drink water with thee in this place: ¹⁷ For it was said to me by the word of the LORD, Thou shalt eat no bread nor drink water there, nor turn again to go by the way that thou camest. ¹⁸ He said unto him, I [am] a prophet also as thou [art]; and an angel spake unto me by the word of the LORD, saying, Bring him back with thee into thine house, that he may eat bread and drink water. [But] he lied unto him. ¹⁹ So he went back with him, and did eat bread in his house, and drank water."

The very First Bit of Bread that this Young Prophet did eat, brought forth Sin, a Separation from The Father’s Commandment. Even though, like Adam, was told by The Father, NOT TO… . Like Adam, a Price For Disobedience MUST be paid.

1 Kings 13:21-24 KJV

"²¹ And he cried unto the man of God that came from Judah, saying, Thus saith the LORD, Forasmuch as thou hast disobeyed the mouth of the LORD, and hast not kept the commandment which the LORD thy God commanded thee, ²² But camest back, and hast eaten bread and drunk water in the place, of the which [the LORD] did say to thee, Eat no bread, and drink no water; thy carcase shall not come unto the sepulchre of thy fathers. ²³ And it came to pass, after he had eaten bread, and after he had drunk, that he saddled for him the ass, [to wit], for the prophet whom he had brought back. ²⁴ And when he was gone, a lion met him by the way, and slew him: and his carcase was cast in the way, and the ass stood by it, the lion also stood by the carcase."

Both were given a Direct Word from The Father and both CHOSE to Walk in Disobedience! Both paid a Price for their Disobedience with their very lives. You Must ask the Question, “What does this do with me, that was in the Old Testament and Jesus has Paid for My Sins…”? The two story’s have everything to do with the here and now. Jesus said that IF we truly Believe in Him, IF we truly Love Him, then what ever Jesus says, we would Do Without Question, Without Disobedience.

Hebrews 13:8 KJV

“Jesus Christ the same yesterday, and to day, and for ever."

John 14:15 KJV

“If ye love me, keep my commandments."

John 10:30 KJV

“I and [my] Father are one."

Many of you Do Not Understand the Weight, the Cost of Sin and Disobedience. Many of you have been taught that because of Grace you can do No Wrong, that Your Salvation Is Secure no matter what. As Jesus has told me time and time again, if Salvation was as simple as “I Believe In Jesus, I Accept Jesus As Savior” then, the New Testament would be all of just those few words. There would be No Need to have any other Writing Of Obedience given to Man. The Whole World could be Saved by just saying, “I Believe In Jesus, I Accept Jesus As Savior”, but Scripture in its entire, both Old Testament and New Testament speak otherwise!

Jesus said that there will be many, many that will Call Jesus Lord, but Jesus will tell them to their face, I Never Knew You and will cast them into the Lake Of Fire.

Matthew 7:21 KJV

“Not every one that saith unto me, Lord, Lord, shall enter into the kingdom of heaven; but he that doeth the will of my Father which is in heaven."

Luke 6:46 KJV

“And why call ye me, Lord, Lord, and do not the things which I say?"

It is Not Enough for any person to say, “I Believe In Jesus, I Accept Jesus As Savior” there Must Accompany Fruit, Actions Of Obedience, a Mind and Heart Change. Yes, the work that Jesus was sent to do, is done, no more does anything need to be done on the Spiritual Side, but on the Physical Side we Must Walk Out Our Salvation! In other words, the Price that Jesus Paid for Our Salvation must be Proven, to Jesus, to Man and to Satan. We cannot say one thing and then do the opposite, we cannot walk in the light while giving place to darkness…what fellowship does sin have with righteousness or light to darkness…they cannot be in Fellowship!!!

Matthew 3:7-8 KJV

"⁷ But when he saw many of the Pharisees and Sadducees come to his baptism, he said unto them, O generation of vipers, who hath warned you to flee from the wrath to come? ⁸ Bring forth therefore fruits meet for repentance:"

Matthew 7:16-19 KJV

“Ye shall know them by their fruits. Do men gather grapes of thorns, or figs of thistles?"

"¹⁷ Even so every good tree bringeth forth good fruit; but a corrupt tree bringeth forth evil fruit. ¹⁸ A good tree cannot bring forth evil fruit, neither [can] a corrupt tree bring forth good fruit. ¹⁹ Every tree that bringeth not forth good fruit is hewn down, and cast into the fire. ²⁰ Wherefore by their fruits ye shall know them."

So then, here is the Deception Of Sin… there are many who Clam Jesus as Savior and even more who Clam Jesus as Lord, but their Lives, that is, their Communications, their Actions, their Thoughts, their Associations, their Soul speaks otherwise. We are told in Scripture that there Must Be A Change, that we Must Bring Our Soul’s, Our Body’s, into Subjection, that is, into Obedience To The Word and Holy Spirit to be Acceptable To Jesus.

Romans 12:1-2 KJV

"¹ I beseech you therefore, brethren, by the mercies of God, that ye present your bodies a living sacrifice, holy, acceptable unto God, [which is] your reasonable service. ² And be not conformed to this world: but be ye transformed by the renewing of your mind, that ye may prove what [is] that good, and acceptable, and perfect, will of God."

1 Corinthians 9:27 KJV

“But I keep under my body, and bring [it] into subjection: lest that by any means, when I have preached to others, I myself should be a castaway."

World Dictionary of “Subjection” - the action of subjecting a country or person to one's control, or the fact of being subjected.

Bible Dictionary of “Subjection” - to lead away into slavery, claim as one's slave, to make a slave and to treat as a slave with severity, subject to stern and rigid discipline.

In other words, that we Must make, let me say that again, WE MUST MAKE our Flesh and all of it’s attributes, Obey The Word Of Jesus, to Do The Will Of The Father. This is not easy, it is a task that only The Holy Spirit can help us with. Our Flesh is at Constant War with The Spirit, non-stop, day and night, awake and asleep we are in a battle.

Now, understand this, Satan Knows Jesus, Satan Knows The Fathers Will and Satan Knows Mankind’s Weaknesses.

James 2:19 KJV

“Thou believest that there is one God; thou doest well: the devils also believe, and tremble."

James 1:14 KJV

“But every man is tempted, when he is drawn away of his own lust, and enticed."

 Satan uses those things that are Weaknesses Of The Flesh, Sin, to Drawn us away from the Will Of The Father, from being Obedient To Jesus. We have seen the very simplest things that Adam and the Young Prophet did to bring forth death by their Acts Of Disobedience in the Smallest Way…in Our Eyes, but in The Fathers Eyes where Great Acts Of Sin.

Brothers and Sisters I cannot stress enough how we must Walk In Obedience, that every Word, every Action that we say and do will hold us Accountable To Jesus for our very lives. It is not an easy task to Walk, there is No Simple way, but only Aggression To Obedience. It is becoming harder to live in this World being attacked on every side to Walk In Obedience, but Jesus said we Must Endure until the end, that is, until we die.

I know the messages that Jesus gives me seem to all surround Obedience and Disobedience, and they do, but consider this, why does this weigh upon the Lord Jesus so much, why is The Holy Spirit pushing that We Walk According To The Fathers Will, Why?

Matthew 24:13 KJV

“But he that shall endure unto the end, the same shall be saved."

2 Timothy 2:3 KJV

“Thou therefore endure hardness, as a good soldier of Jesus Christ."

Amen and Amen!!!

Email: godsonlyfoundation@gmail.com

Website: ApostleLee.com