🌏 Blogs / Articles / News / Classifieds / Press Releases / PSA / Podcast / Poetry / Storytelling

 

flaw (1)

f:id:bkneddy:20190812180803j:plain

Ut flaw detector is a conventional product with high density, moderate noise. The system is suitable for the automatic detection of internal and external defects of various steel bars.

The principle of Digital Ultrasonic Flaw Detector is that after the ultrasonic wave is coupled into the steel rod by water, the incident propagation will case ultrasonic reflection when there is a defect in the bar. The ultrasonic instrument will alarm the ultrasonic reflected signal after the amplified signal to realize the automatic detection of the defect.

Wireless Transmission Steel Bar Ultrasonic Flaw Detector Brief

  1. Probe configuration on spindle section 1

There are two probe regulators in section 1,180 degrees apart. Each regulator is equipped with a two-channel combination of ultrasonic line focus probes, and the transverse wave incident clockwise.

Detection of defects: detection of round subcutaneous defects in a rounded clockwise direction

Center frequency: 5.0MHz ± 10%

Coupling method: water immersion method

Quantity: 2 sets of probes, each set consisting of 2 combined wafers, which are evenly distributed in the circumferential direction of the workpiece, 180° apart, on the same section. A total of 4 independent channels.

  1. Probe configuration on the main shaft section 2

A total of 2 probe adjustment frames are placed on section 2, each separated by 180°, and a 2-channel combined ultrasonic line focusing probe is arranged on each adjustment frame, and the longitudinal wave is incident.

Detection of defects: metallurgical defects inside the steel bar,

Detection range: center transverse hole.

Center frequency: 5.0MHz ± 10%

Coupling method: water immersion method

Quantity: 2 sets of probes, each consisting of 2 combined wafers. These 2 sets of probes are evenly distributed in the circumferential direction of the workpiece, 180° apart, and there are 4 independent channels in the same section.

  1. Probe configuration on the main shaft section 3

A total of 2 probe adjustment frames are placed on section 3, each separated by 180°, and a 2-channel combined ultrasonic line focusing probe is arranged on each adjustment frame, and the transverse wave is incident counterclockwise.

Detection of defects: counter-clockwise detection of round subcutaneous defects

Center frequency: 5.0MHz ± 10%

Coupling method: water immersion method

Quantity: 2 sets of probes, each consisting of 2 combined wafers. These 2 sets of probes are evenly distributed in the circumferential direction of the workpiece, 180° apart, and there are 4 independent channels in the same section.

f:id:bkneddy:20190812180754j:plain

Defect detection standard

GB/T4162-2008 Ultrasonic testing method for forged steel bar.

Wireless Transmission Steel Bar Ultrasonic Flaw Detector Parameters

Channel number

12 channels

Flaw detection speed

30m/min

Total gain

100dB,step0.5dB

Working mode

Single probe transmitting, receiving or double probe transmitting and  receiving respectively

Sensitivity margin

≥50dB

Resolving power

≥26dB

Dynamic range

≥30dB

scan range

0~5000mm

Frequency range

0.5~20MHz

Sampling range

250MHz

Repetition range

Single channel100Hz~4KHzadjustment

Vertical linearity

≤2%

Horizontal linearity

≤1%

Detection mode

Full-wave, positive half-wave, negative half-wave

Gate setting

Each channel has three gates, A and B are defective gates and C are interface tracking gates.

Alarm indication

Color Display and Sound Alarm of A, B and C Gate Alarm on Each Channel

Delayed alarm

Two path,delay time 0.1-10s,step 0.1s

Waveform storage, unlimited number, waveform playback, printing and report generation.

 

We are one of the leading non destructive testing equipment manufacturers, RFQ today!

Read more…

🔥Christian Music News